Electrical Heaters - Oil & Gas Equipment

Electrical Heaters

The following products are made in Europe:

Space Heaters

Space heaters for safe area, these heaters are designed for anti-condensation, freeze protection and temperature maintenance.  Power consumption: 50-100-150W

Flame Proof Space Heaters

Space heaters for hazardous locations, these heaters are designed for anti-condensation, freeze protection and temperature maintenance.
Installation ZONE 1-2-21-22
Atex Category II 2GD
Type of Protection Exd IIC T4 / T3 Gb
Ex tb IIIC T135 to 200°C Db (IP66)
Power consumption: 50-100-300W

Heating Elements

Tubular elements are the most versatile and widely used type of electric heating elements for industrial applications because of their compacted granular insulation, they give long life in a variety of rugged environments. They can be bent to virtually any shape, they can be finished in an almost endless variety of diameters, lengths and sheet materials. Our range of Electric Immersion Heaters is made to heat water, oil and chemical. These are made from superior grade of copper, stainless steel and titanium pipe, and known for their efficiency and long lasting performance. Range of immersion heaters is available with easy installation and accurate control that makes these heaters highly useful in many industrial heating processes. These are suitable for heating various liquids, viscous materials and solid materials with low melting points. Our immersion heaters are based on latest technological advancements.

Air Duct Heaters

Air duct heaters designed for flange mounting in connection with climate control/heat regeneration and ventilation system, heaters usually used for room comfort heating.
Special design for example for Process systems, Furnaces, Autoclaves, Reheating, Paint drying, Load banks, Ships and high-temperature duct heaters upon request.
Other Typical uses include, air tempering in the ventilation systems of large buildings and accommodation areas of  hips and offshore platforms, process drying equipment, recirculating ovens.
All heaters are designed to meet clients specific design requirements.
Features
Case: Stainless steel, Galvanised steel or Painted steel.
Elements: Tubular element unfinned or finned, with mild or stainless steel sheath.
Enclosure: Direct or stand off construction with safe area protection IP42
to IP66 and ATEX/IECEX for hazardous areas.
Sensors: thermostatic, thermocouple or RTD temperature sensors.
Controls: Stand alone control panels available or built-in to the heater terminal enclosure.

Flameproof (Explosion proof) industrial flanged
and screwed immersion heaters for zones 1&2
Hazardous areas, gas groups IIA, IIB&IIC
temperature class T1 to T6.

Flanged Immersion Heaters

They are made of heating elements welded on flanged UNI, ANSI connections or to Customers specifications, in any type of material. On request, they came with automatic safety devices (thermostat,

Thermocouple, RTD temperature sensors, etc.).

Terminal box with IP66/67 degree of protection.

These heaters can have a terminal box fixed directly on the flange connection (hot head) generally used for normal applications or with the detached terminal box (cold head) from the connection for high temperature applications.

Screw-On Immersion Heaters

They are made of heating elements welded on male screw type Gas, NPT, Metric in any type of material. On request, they came with an automatic safety thermostat or with manual reset. Terminal box with IP65 degree of protection. These heaters can have a terminal box fixed directly on the screw connection (hot head) generally used for normal applications or with the detached terminal box (cold head) from the connection for high temperature applications.  The electric heating elements are constructed with high quality 80/20 nickel chrome resistance wire, centered in a metal tube and insulated with compacted magnesium oxide.  The element tube material generally used includes:- carbon steel, stainless steels 304, 316, 321 Incoloy 800 & 825, Inconel 600, 625, Titanium, Copper, Monel, and other available materials.  Flameproof (Explosion proof) industrial flanged and screwed immersion heaters for zones 1&2.

Hazardous areas, gas groups IIA, IIB&IIC temperature class T1 to T6.
The elements are either welded or brazed to the flange, which is available in a variety of materials to suit the element sheath and the application. Connection flange type UNI or ANSI or a Customer’s drawing.  For Applications where the operating temperature is not high the terminal box is attached directly to the flange. For high temperature the terminal box is stood off varying distances depending on the operating temperature.  The heaters are complete with thermostat and manual reset safety cut out.

Cartridge Heater Atex

• Cartridge flanged and screwed heaters allow heating elements to be changed without decommissioning the tank
• Certified for ATEX Hazardous Area Zone 1 & 2
• In accordance with API-614 standards
• Certified II2G – Exd IIC T6-T3 Gb as per Standards CENELEC EN 60079-0 / 60079-1
• Maximum voltage up to 750 V
• Maximum Power up to 500 kW
• Elements available in copper, carbon steel, stainless steels 304L, 316L, 321, Incoloy®, Inconel®
• Flange available in carbon steel or stainless steel

Convector Heaters Series RAEx II 2G

The Convector Heaters series RAEx are designed to heat ambient air in hazardous (classified) areas; they can be supplied
for use in potentially explosive Gas atmospheres (II 2G), or in both potentially explosive Gas & Dust atmospheres (II GD)
Series RAEx II 2G II 2 GD Ex d IIC T4T3T2 Gb -60°C = Ta = 60°C Ex tb IIIC T135 ÷ T300°C Db IP65 -60°C = Ta = 60°C

Exchanger

F.A.T.I. can offer you a wide variety of electrical exchangers in special construction fully in accordance with clients  specifications and requirements. Electric circulation heaters and process heating systems for heating a wide range of industrial liquids and gases.
Mechanical design codes include ASME, BS5500, ISPESL(PED), STOOMWEZEN, TEMA, AD MERKBLATTER, or any other recognized code.

ATEX – Eexd Threaded Heaters

Explosion proof industrial screwed immersion heaters for zones 1 &2 Hazardous areas, gas groups IIA, IIB, & IIC temperature class T1-T6 Certification ATEX II 2G EX D IIC EN 60079-0 / 60079-

ATEX – Eexd Duct Heaters

Air duct heaters are designed for flange mounting in connection with climate control / heat regeneration and ventilation systems, heaters usually used for room comfort heating. Special designs, for example, Process systems, Furnaces, Autoclaves, Reheating, Paint drying, Banks, Ships and high temperature duct heaters on request.

Electrical Threaded Heaters

Screw Plug Immersion Heaters consist of tubular elements welded or brazed into a threaded screw plug which can then be inserted into a threaded opening in a tank wall or through a mating full or half coupling.

Electrical Elements

Armoured elements made up of an Ni Cr 80-20 coil sealed
in high quality magnesium oxide (MgO).

Electrical Duct Heaters

Armoured electric duct heaters for heating air in safe zones, with a mechanical protection level of IP40, IP55, and IP65 are recommended for use in an infinite number of applications and industrial processes, to heat air or gas flows

ATEX – Eexd Flanged Heaters

Our range of immersion heaters is suitable for heating all process fluids which are non-corrosive to the materials of construction for installation in Hazardous area Zone 1 & 2.

Electrical Flanged Heaters

Ideal for generating steam and heating gases and liquids in pressure vessels and tanks, flanged immersion heaters are hairpin-bent tubular elements welded into a flange and provided with electrical enclosures.

Electrical Heat Exchangers

Electric heat exchangers for heating all types of gas or liquids.

Electrical Panels

We have a great deal of experience in thyristor controls (SCRs) used to regulate the temperature of electric heaters – from a few kW up to more than 5 MW – used in industrial, chemical, petrochemical, geothermal, and technical gas processes.

Transformers

Power transformers in resin, Power transformers in oil.

Air-conditioned cabins with electrical control panels complete with transformer.

Convector Static Air Heater

Hazardous area convector heaters are designed for heating areas where there are presence of flammable atmosphere groups IIA, IIB or IIC located in zone 1 or 2.

Galvanic Teflon Heater

Electric heaters for galvanic and corrosive solution baths

Heaters for Drum

Heaters for heating drums of any size or capacity.

Also executions for ATEX certified hazardous zones available.

Cast and Strip Heater

Metal or ceramic cast or strip heaters for heating dies and extruders.

Cartridge Heater

Low density cartridge up to 5 w/cm2, normally used when working conditions are not particularly severe.

© 1997 - 2018 Go-on Group Business Development.  All rights reserved.